newbg

JXSC Rock Gold Mining Process Methods

JXSC Rock Gold Mining Process Methods

Release time:25 October 2018

Jiangxi Shicheng Mine Machinery Factory is a leading mining machinery manufacturer with over 30 years experiences,providing complete set processing equipments for Gold ore 、Tin ore、Tungsten ore、Iron ore、Diamond ore、Coltan ore、Silica sand、Zircon sand、Black sand、Chrome ore,ect. As well as complete set small lab mining machines.

 

For hard quartz rock gold mining process,it usually contain below 3 separation methods:

 

Gravity Process for Rock Gold Mining:

 

1.Crushing and Grinding stage

The extracted ore should be crushed by jaw crusher initially and then by fine crusher.When it gets the reasonable fineness,it is transported into ball mill by elevating conveyer and feeder,and is milled by ball mill.

 

2.Classifying stage

The subtle milled ore gets the next procedure:classification.There is a theory that if the weights of solid particles are different,the sedimentations will be different,and the mixed ore can be classified by spiral classifier/screw classifier.

 

3.Beneficiation stage

The super fine particles from ball mill will feed into shaking table through the hydraulic classifiers,which can ensure different size distribution ore/slurry feed into different riffles shaking table,in order to reach a higher recovery ratio.

JXSC Shaking Table is one of our flagship mining equipment with more than 30 years experiences.It enjoys very high,up to 95%high recovery rate which widely used to concentrate free gold.

 

4.Gold refining stage

Mercury Distiller/Gold Amalgamator is the traditional gold refining machine,widely used to mix the mercury and gold concentrate,in order to get the pure gold,then we can use Gold melting furnace to produce gold bar.

Gravity Process for Rock Gold Mining

Flotation Process for Rock Gold Recovery:

 

1.Crushing and Grinding stage&2.Classifying stage are the same as Gravity process.

 

3.Mixing and Flotation stage

The classified ore gets into mixing tank for fully mixing.At this stage,chemical agent for foam can be added.After fully mixing,the slurry will enter into flotation machine.

When the flotation machine works,the motor drives the impeller to revolve,so the centrifugal effect and negative pressure are produced.On one hand,ample air is absorbed and mixed with mineral slurry,on the other hand,the mixed mineral slurry is mingled with additive, meanwhile, the foams are thinning,the mineral is bounded with foams,and floats up to the surface of mineral slurry and the mineralized foam is formed.The liquid surface can be adjusted with the height of adjustment flashboard,so that the useful foams are scraped with squeegee.

 

4.Concentrator thickening and drying

Then gold is separated from others.Since the separated ore are wet,they should be dewatered by thicker initially,and dried by dryer.

JXSC mine machine factory

Leaching and adsorption for Rock Gold Recovery:

 

The slurry (1) of ground ore and lime moves into a series of six leach tanks (2) where a sodium cyanide solution is added. The tanks provide sufficient retention time to allow the gold and silver to be dissolved by the cyanide solution. Oxygen is added to assist in this process.

 

The slurry then moves through a series of carbon adsorption tanks (3). While the leaching process continues in these tanks,the primary objective is to remove the gold and silver from the solution. To achieve this,carbon is fed through the tanks(4)and the gold and silver adsorbs (attaches) to the carbon granules.Carbon is heated to 600 degrees C and fed into the circuit in the opposite direction to the slurry flow,moving from the last adsorption tank to the first.This is because the gold and silver move towards the carbon via a diffusive process.It is necessary to have‘fresh’carbon at the end of the chain,to scalp the gold and silver that has not been removed in the previous tanks.

 

By the time the slurry reaches the final adsorption tank,most of the precious metals have been removed.The barren slurry,now known as tailings,is pumped to the tailings storage facility (5).In contrast,by the time the carbon reaches the first adsorption tank it has recovered most of the gold and silver from solution.This‘loaded’carbon is then pumped to the elution circuit (6) where the gold and silver is washed off with superheated water.The washed solution,called pregnant eluate,is passed to the electrowinning circuit (7). The remaining barren carbon is reactivated by acid washing and kilning and returned to the adsorption tanks.

Leaching and adsorption for Rock Gold Recovery

LATEST PRODUCTS